Various automatic machines

 Contact Semi-Automatic Inspection Machine

Semi-automatic inspection machine for two model numbers with different notch angles

This is a contact-type semi-automatic inspection system that clamps a workpiece between the top and bottom set of Keyence GT2 (contact-type displacement sensor) and measures the inside groove, notch, and spot-welded bracket height of a thin pipe.

Originally, human judgment was made using a drop gauge, but it is extremely difficult to continue inspecting micron units quickly and accurately.

By automating only the measurement while the loading and unloading of the workpiece is performed by a human operator, human error is eliminated, which not only reduces the workload of the operator, but also improves the reliability of the measurement data.

use

Measurement of complex carburetor components

cycle time

6 sec /PC

output

Approx. 4,000 pieces /day (1 shift)

 Automated Assembly Machine

Automated Assembly & Inspection Machine

use

Ring assembly into nipples
Inspection

　1. nipples length check
　2. penetration test

　3. camera check: ring positions

 Reamer Gauge Inspection Machine

Reamer Gauge Inspection Machine

This machine covers 8 different models for reamer and Go/No-Go gauge check

use

for reamer and Go/No-Go gauge check

cycle time

5 sec /PC

2 sec /PC  *only gauge check

output

Approx. 5,500 pieces /day (1 shift)

Approx. 12,000 pieces /day (1 shift) *only gauge check

 Precision Shaft O.D. Inspection Machine

Two-point O.D. measurement + Single-point O.D. measuring instrument

This product must guarantee an outside diameter of 3.175-3.180 mm (tolerance range 5 microns).

A shaft falling from a carrier is measured at two points by pressing a plate contactor against it while sliding the shaft. The shaft is checked for taper at the tip and at the two end points to determine if it is good or bad.

use

Outer diameter inspection of precision shafts

cycle time

90 pcs /min

output

Approx. 85,000 bottles / day (1 shift)

 3-point O.D. measuring machine

Adoption of Keyence laser sensor enables sub-micron measurement

The shaft being measured is a long shaft of 4 mm diameter, but the tolerance range of 3.987-3.992 mm must be guaranteed. It is made of SWRH62A, a hard steel wire material, and is subject to heat treatment, which causes runout, bends, and variations in outside diameter, making it a difficult product.

The laser captures the shaft as it passes through the V-block and measures three points: the top, middle, and end of the workpiece.

By employing a Keyence laser sensor, measurements can be made with sub-micron accuracy, enabling outer diameter inspections with a range tolerance of 4 to 5 microns.
 

use

Outer diameter inspection of precision shafts

cycle time

60 pcs /min

output

Approx. 20,000 bottles/day (1 shift)

reference price

US$45,000.-/unit, including customs clearance, side-hauling, installation, training, etc.
(In the case of selling this equipment in Thailand)

 5-point O.D. measuring machine

5-point measuring instrument for precision shafts over φ8 mm O.D.

The shafts of blower motors used for air conditioning and battery cooling in vehicles, must be guaranteed to have an outside diameter tolerance of 6 microns. The shaft must guarantee an outside diameter tolerance of 6 microns. Because of its large diameter and relatively long length, it is difficult to control runout and taper over its entire length.

Once this type of defect is released, a huge amount of labor and cost is incurred in the sorting process, We have introduced this sorting system in order to handle this sorting process correctly and as early as possible within the company.

This is a sorting machine based on the concept of "accurate inspection and low-cost production. The machine is equipped with a V-shaped jig to receive the workpieces and automatically check them for correctness.The workpiece is received by a V-shaped jig and clamped from both sides by a contact-type measuring device.

use

Outer diameter inspection of precision shafts

cycle time

Approx. 10 pcs /min

output

Approx. 3,500 bottles /day (1 shift)

 Custom Automated Machines and Custom Automated Assembly Machines

► Product example 1: Anchor bolt automatic assembly machine

Automatic assembly of 4-5 items such as bolts, sleeves, washers, nuts, etc.

use

Installation of soundproof walls, elevator frames, and other vibrating equipment

cycle time

25 pcs /min

output

Approx. 10,000 units /day (1 shift)

reference price

Baht 2,990,000 (incl. factory installation)

lead time

4 months

► Product example 2: Drop-in anchor automatic assembly machine

Assembles sleeves, pins, and plastic blocks at high speed

use

Pipe hanging fixture installation, air conditioning duct installation, cable rack installation

cycle time

50-60 pieces /min

output

Approx. 20,000 units /day (1 shift)

reference price

Baht 2,490,000 (incl. factory installation)

lead time

4 months

► Product example 3: Automatic spray nozzle assembly machine

Four outputs at a time

use

Spray nozzles

cycle time

80 pcs /min

output

Approx. 30,000 units /day (1 shift)

reference price

Can be provided at about half the price compared to products made by Japanese, European, and U.S. companies (Depending on the customer's specifications)

lead time

5-6 months

► Product case 4: Automatic spray nozzle assembly machine

Automatic assembly of 3 parts:
(1) piston parts, (2) housing, and (3) nozzle