Cleaning Agents

『METAL CLEANER』　～Cleaning Agents～

To be quick dry cleaning agents with non-fluorocarbon and/or non-chlorine. This applies to removal such as oil, grease, dust, etc. on surface of mould or metal parts. Also, it can clean even though resin with hard chemical resistance like PP.
※Liquid type (Metal cleaner L) is also available.

『JET CLEANER』　～Cleaning Agents (Strong) ～

To be cleaning agents with contains strong effective power. This applies to removal such as oil, grease, dust, etc. on surface of mould or metal. Moreover, it can easily clean permanent marker and/or blue varnish just spraying.

『EZ CLEANER』　～Mould and Parts Cleaning Agents (Quick dry) ～

To be quick dry cleaning agents with non-fluorocarbon and/or non-chlorine.
This applies to removal such as oil, grease, dust, etc. on surface of mould or metal parts. Also, it can use for cleaning plastic and/or metal products.
※Liquid type (EZ cleaner L) is also available.

『MILD CLEAN』　～Mould and Products Cleaning Agents～

To be the best cleaning agents for plastic products, mould and machinery parts.
It has hardly effect to plastic or rubber, etc. In addition to, its feature is no likely white on surface after drying.
※Liquid type (Mild cleaner L) is also available.

『LIMO-CLEAN』　～Alcohol type, Cleaning Agents～

To be alcohol-based cleaning agents that contains a combination of natural components included in the skin of citrus fruit. It is suitable for applied to removal such as oil, grease, dust, etc. on surface of mould or metal parts. In additional, it can be applied to remove tar or gas on mould. The permanent marker can also be removed easily.
※Container: 5 litre/gallon

『GAS TRICK』　～Gas and/or Tar Removal Agents (Spray)～

To be easily removal spray such as adhesion of gas or tar on mould. This is the type that smell and toxicity are extremely few. Please directly spray on gas or tar, or spray on waist and swab on mould. Then, shot loss after leave for 4-5 minutes, and remove by air-blow or Metal Cleaner.

『MOLD BRIGHT』　～Gas and/or Tar Removal Agents (Foam Spray)～

To be gas removal agents with foam for injection mould or mould maintenance. This applies to removal of the stubborn adhesive on mould. And also, it is effectiveness for the burn-up adhesive at screw of injection machine. It becomes foam after spraying on mould, but after foam went out, please shot loss and/or cleaning by air-blow.

『MOULD FRESH』　～Gas and/or Tar Removal Agents (Liquid)～

This agent is effectiveness for peeling gas and/or tar off from mould, not only adaption resin, but also POM, PA66 or flame retardance like ABS, etc. It is a type safe for the human body. Apply to a little bit on gas and/or tar and wipe off with soft brush or cloth.

『AQUASOL WCA-3』　～Cleaning agents for ultrasonic cleaning machine～

It is a safety high solubility cleaning agent, easily remove the dirt such as oil, gas or tar adhering to the mold. Very economical, able to dilute with water 12 times to use depend on the degree of the dirt. It can also be used as a cleaning solution for ultrasonic cleaning machine.

『AQUASOL RINSE B』　～High solubility anti-rust agents for mould and metal parts～

It is a safety high solubility anti-rust agent, able to use in the rinsing of the mould and metal parts after cleaning with Aquasol. Very economical, able to dilute with water to use depend on anti-rust period. ※ 25 times dilution (about 3 months) to 50 times dilution (a short time anti-rust)

『GPK-1』　～Soft Alkaline Cleaning Agents～

To be alkaline cleaning agents, apply to ultrasonic cleaning machine with water-based. To dilute with drinking water about [1:5 ~1:10] before cleaning. In case of using sprayer, dilute with water about [1:10~1:50] depend on the stain extent.